Home > Product > Fasson > 05596

Print this Page
50# DSXTM FSC®/S100R/40#SCK
Spec# 05596-REV 1/2019F
Facestock:
50# DSX™ FSC® is a bright white, high-strength EDP paper specially designed for enhanced continuous laser imaging, variable imprinting, and high speed converting.  This facestock has excellent smudge resistance.  Prints well by offset, and offers fair printing with solvent and water-based flexo and screen methods.

The FSC® certification ensures that products come from well managed forests which provide environmental, social, and economic benefits. The FSC® chain of custody certification verifies that FSC® certified material is identified or kept segregated from non-certified or non-controlled material through this chain.



Basis Weight:
48# per ream
(500 sheets 25" x 38")


Caliper:
0.00337 inches ± 10%


Tensile:
MD 25# per inch width
CD 17.50# per inch width


Tear:
MD 55 grams
CD 50 grams


Stiffness:
MD 92 mg
CD 57mg

Adhesive:
S100R is a permanent adhesive which is removable in minimum 100° F water. Developed with good initial tack and ultimate adhesion, S100R can be used as a permanent adhesive on many substrates, yet be removed from that substrate after immersion in water hotter than 100° F. Removal times will vary due to differences in facestocks and substrates. It might be as short as 30 seconds from HDPE, or as long as 5 minutes. Where removal is required, this adhesive is recommended for use on HDPE, polypropylene, poly vinyl chloride (PVC), polyester, Lexan®, stainless steel, and glass. We do not recommend it for use with film facestocks (i.e., polypropylene, polystyrene), due to a potential surface interaction which could cause the loss of water removability. This adhesive exhibits excellent diecutting and stripping properties.

FDA Compliance:  Title 21, Section 175.105 of the Code of Federal Regulations (21 CFR 175.105).  Compliance to this regulation permits the use of this adhesive in applications for which the adhesive either (1) is separated from the food by a functional barrier, which will prevent the migration of any of the adhesive components to the food, or (2) has incidental contact with food limited to the trace amount at the seams or the edges of the label.

Lexan® is a registered trademark of General Electric Company.



Type:
Emulsion Acrylic


Minimum Application Temperature:
+20° F


Service Temperature Range:
-65° F to 200° F


Typical Performance Data: 60# C1S Paper at room temperature on standard lab panels



Stainless Steel
Loop Tack:
Peel Adhesion:

2.6 lbs
1.8 lbs - Tear


HDPE
Loop Tack:
Peel Adhesion:

1.6 lbs
1.1 - 1.6 lbs


PET
Loop Tack:
Peel Adhesion:

2.6 lbs
1.2 lbs -Tear


Glass
Loop Tack:
Peel Adhesion:

2.7 lbs
1.9 lbs -Tear






Liner:
40#SCK is a bleached super calendered kraft stock featuring high internal strength, toughness, and tear resistance. Used primarily for roll-to-roll label applications.



Basis Weight:
39.90# per ream ± 10%
(24" X 36" 500 sheets)


Caliper:
0.00236 inches ± 10%


Tensile:
MD 38.30# per inch width
CD 14.80# per inch width


Tear:
MD 32.60 grams
CD 40.80 grams

Total Construction Caliper (approximate): 0.00657 inches ± 10%

Applications and Uses
This adhesive can be used as a permanent adhesive on many substrates yet be removed from that substrate after immersion in water hotter than 100°F.  Removal times will vary due to differences in facestocks and substrates.  It might be as short as thirty seconds from HDPE, but could be as long as five minutes.  When removal is required, this adhesive is recommended for use on HDPE, PVC, PET, LEXAN™, stainless steel, and glass.  We do not recommend it for use on polypropylene or polystyrene due to a potential surface interaction, which could cause the loss of water removability.

Optimal Storage Conditions
Unless otherwise specified in this document, ideally store at 72F and 50% RH